VMware VCENTER APPLICATION DISCOVERY MANAGER 6.1 - REPOSITORY Uživatelský manuál Strana 84
- Strana / 220
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
OneCommand™ Manager Application P007997-01A Rev. B
8. Managing Adapters and Ports
FC/FCoE
84
“Not Present” if boot code is not loaded. If boot code is not loaded, the
Enable Adapter boot checkbox is not visible and you cannot configure the
selected port to boot from SAN.
Enable adapter boot checkbox – Check this box if you want the adapter to load
and execute boot code during system startup. Click Configure Boot to
configure boot from SAN. See “Configuring Boot from an FC SAN” on page 183
for more information. (Not available in read-only mode.)
Note: The Enable Adapter boot check box is not available via the CIM
interface.
Note: Enabling adapter boot only causes the adapter to load the boot code and
execute it during system startup. It does not mean that the adapter will
boot from SAN. To boot from SAN, the boot type must be enabled. Do
this in the Boot from SAN configuration window for each boot type. In
addition, the BIOS must be configured to boot from SAN.
WWN Management Area
Note: COMSTAR ports are supported on Solaris 11 only.
Current
WWPN – The World Wide Port Name for the selected adapter port.
WWNN – The World Wide Node Name for the selected adapter port.
Pending Changes
WWPN – Works in conjunction with the Change WWN button. Displays the
World Wide Port Name you assigned for the selected adapter port, but the
system must be rebooted for these changes to take effect and appear under the
“Current” listing. See “Configuring Boot from an FC SAN” on page 183 for
more information.
WWNN – Works in conjunction with the Change WWN button. Displays the
World Wide Node Name you assigned for the selected adapter port, but the
system must be rebooted for these changes to take effect and appear under the
“Current” listing. See “Configuring Boot from an FC SAN” on page 183 for
more information.
Maintenance Tab Buttons (Not available in read-only mode.)
Download Firmware – Click to update firmware on the selected port. See
“Updating Adapter Firmware” on page 178 for more information.
Configure Boot – Check Enable adapter boot and click Configure Boot to
configure boot from SAN. See “Configuring Boot from an FC SAN” on page 183
for more information. (Not available on VMware ESX servers being managed
through the CIM interface.)
Change WWN – Click to change the selected adapter port's World Wide Node
Name or World Wide Port Name. See “NIC” on page 144 for more information.
- OneCommand™ Manager 1
- Application 1
- Version 6.1 1
- User Manual 1
- Table of Contents 3
- Table of Contents 4
- List of Figures 10
- List of Figures 11
- List of Tables 13
- 1. Introduction 14
- Compatibility 15
- Known Issues 16
- Abbreviations 16
- In Windows 18
- In Linux 20
- For RHEL 5 and RHEL 6 type: 21
- In Solaris 22
- In VMware ESX Server 24
- --maintenancemode update 25
- Web Launch Interface 26
- Installation 27
- Solaris: 28
- Linux: 28
- Web Launch Interface Only 29
- /opt/ELXocm/wsuninstall 30
- Manager Application 31
- Launch Interface 32
- Element Definitions 34
- Menu Bar 35
- Toolbar Buttons 35
- Discovery-Tree 37
- Property Tabs 38
- Status Bar 39
- Management Host 40
- 2. Run the following script: 41
- 5. Configuring Discovery 42
- Hosts File 43
- Adding a Single Host 45
- Adding a Range of Hosts 46
- Removing Hosts 48
- Adding Target Portals 52
- Removing a Target Portal 52
- Figure 5-7 iSCSI SNS Tab 53
- Logging into Targets 54
- Removing Targets 55
- Viewing Target Sessions 56
- Session Statistics Area 58
- Connection Information Area 59
- 7. Managing Hosts 61
- Function Summary Area 62
- Grouping Hosts 64
- Managing Host Groups 65
- Creating a Host Group 66
- Deleting a Host Group 66
- Adding a Host to a Host Group 67
- Restoring a Host Group 67
- Restoring all Host Groups 67
- Searching for Hosts 68
- Using CIM 69
- Viewing FC Port Information 71
- Viewing FCoE Port Information 73
- Figure 8-4 Statistics Tab 76
- Firmware Area 83
- WWN Management Area 84
- Mapping Information Area 87
- /usr/sbin/lpfc/lun_scan all 88
- LUN CapacityArea 89
- LUN Masking Area 89
- Current Settings Area 90
- Current Mappings Area 90
- Display Mode Radio Buttons 90
- Target Mapping Buttons 92
- Figure 8-14 LUN Masking Tab 93
- Changing Automapping Settings 95
- Adding a Persistent Binding 95
- Figure 8-18 Maintenance Tab 99
- Creating Virtual Ports 101
- 5x:xx:xx:xx:xx:xx:xx:xx 102
- 10:00:xx:xx:xx:xx:xx:xx 102
- 2x:xx:xx:xx:xx:xx:xx:xx 102
- 3x:xx:xx:xx:xx:xx:xx:xx 102
- Deleting Virtual Ports 103
- Figure 8-22 Virtual Port Tab 104
- Figure 8-24 Reset Warning 107
- Activation Requirements 108
- Setting Driver Parameters 110
- Resetting All Default Values 112
- Parameter Value 112
- DCB Settings Area 118
- CIN Settings Area 119
- DCB Tab Field Definitions 120
- Viewing iSCSI VPD Information 126
- Viewing iSCSI Statistics 127
- Viewing iSCSI LUN Information 131
- Viewing iSCSI PCI Registers 133
- DCBX Settings Area 136
- LLDP Settings Area 137
- PFC Priorities Area 137
- ETS Priority Groups Area 137
- Advanced TCP/IP Configuration 140
- Initiator Login Options Area 142
- Authentication Area 142
- Viewing NIC Port Information 144
- Viewing NIC VPD Information 146
- VPD Table Definitions 147
- Base Host Operating System 153
- Guest Host Information Area 154
- Operating System 155
- OneConnect Adapters 156
- Viewing ASIC Information 158
- Personality Area 160
- License Features Area 160
- Showing Licenses 162
- Installing Licenses 163
- Boot Code Versions Area 166
- PHY Data Field Definitions 169
- Error Rates Area 170
- Counters Area 170
- Module Attributes Area 171
- Diagnostic Data Area 172
- Linux Considerations 173
- Enabling Authentication 173
- DHCHAP Tab 175
- Changing Your Password 177
- 10. Updating Adapter Firmware 178
- Boot Types 183
- Boot Device Parameters 184
- 100 ms 191
- 200 ms 191
- 12. Exporting SAN Information 193
- 13. Diagnostics 194
- Information 195
- Viewing Flash Contents 195
- Viewing Overlay Details 196
- Viewing the PCI Registers 196
- Running a Quick Test 196
- Using Beaconing 197
- Creating Diagnostic Dumps 198
- LightPulse FC HBA Diagnostics 199
- Running Loopback Tests 200
- Loopback Test Combinations 201
- Saving the Log File 203
- OneConnect Diagnostics 204
- FCoE End to End Echo Test 206
- Error Action 206
- Test Cycles 206
- Test Pattern 206
- Test Status 206
- 14. Troubleshooting 211
- Situation Resolution 212
- Application Situations 214
- ./stop_ocmanager 215
- Situations 219
Související produkty a manuály pro Software VMware VCENTER APPLICATION DISCOVERY MANAGER 6.1 - REPOSITORY
Software VMware VCM 5.3 - CONFIGURATION MANAGER SECURITY ENVIRONMENT REQUIREMENTS Uživatelský manuál
(32 stránky)
(32 stránky)
Software VMware VCENTER CONFIGURATION MANAGER 5.3 - SOFTWARE CONTENT REPOSITORY TOOL GUIDE Uživatelský manuál
(35 stránky)
(35 stránky)
Software VMware VCENTER CONFIGURATION MANAGER 5.3 - SOFTWARE CONTENT REPOSITORY TOOL GUIDE Uživatelská příručka
(73 stránky)
(73 stránky)
Software VMware NetApp FAS 2050HA Specifikace
(40 stránky)
(40 stránky)
Software VMware vSphere 4 Uživatelská příručka
(71 stránky)
(71 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce